On certain Bafang systems, Error 24 means there's a problem with the light sensor. But Bafang has used different displays and controllers over the years, so check the manual for your particular setup.
Bafang E-Bike Error 24: How to Fix It
Written by: Chris Van Leuven | November 15, 2026 | Time to read: 5-6 min
Bafang Error 24 may indicate a light sensor fault. Learn what causes it, how to check the wiring, and when to contact a mechanic.

More about the Author: Chris Van Leuven
Chris is a writer, climber, and founder of Yosemite E-Biking in Mariposa, CA. When he’s not tackling Sierra Foothills trails or scaling rock walls, he’s crafting adventure stories with his boxer, Fenster. His work has appeared in Outside, Men’s Journal, Gripped, and Best American Sports Writing.

👋 Welcome to Upway!
Table of Contents
My Early Experiences With Bafang E-Bikes
I’ve burned through a lot of e-Bikes over the years. Some I converted, some were hand-me-downs, and others I simply rode too hard. It’s extraordinarily hilly where I live, and I don’t exactly take it easy on my bikes. Between the steep climbs, thousands of feet of elevation gain, and the way I ride, I’ve broken more than a few.
In my early days of e-Biking, after continually burning out the motor on a 250W rear-hub e-Bike, I ordered a conversion kit and rebuilt the bike into a powerful Bafang mid-drive system. Honestly, I would’ve saved money and time had I just bought a certified pre-owned e-Bike from Upway for up to 60% off. It probably would’ve been a safer ride, too!
That converted bike had plenty of problems of its own. Whenever I hit washboard roads, the chain would pop off. And the huge battery I'd installed made the bike so top-heavy that I could barely park it on a slope without it falling over. The kickstand was pretty much useless. More than once, I'd come back to find the bike lying on its side, sometimes with another part of the drivetrain damaged.
What Does Bafang Error 24 Mean?
Error 24 is among the codes listed for certain Bafang conversion-kit displays, including the 850C display used with some BBS02 systems. However, that doesn’t mean every BBS02 or BBSHD conversion kit will generate this warning, which is sometimes displayed as 24H.
The light sensor helps control the e-Bike’s lighting system, including when the headlight turns on automatically, if the bike has that feature. But getting Error 24 doesn't necessarily mean your headlight is broken. The problem could be in the wiring, display, or controller, which makes figuring out what's actually wrong a little more complicated.
Bafang has produced numerous motors, controllers, and displays over the years, and their error codes aren’t always identical, so check your display manual before troubleshooting.

Understanding Other Bafang Error Codes
Error 24 is just one of the warnings that can appear on a Bafang-equipped e-Bike. Depending on the system, other codes can point to motor Hall sensor problems, controller faults, overheating, battery voltage issues, or communication faults.
For example, Bafang Error 08 identifies an abnormal motor Hall sensor signal on applicable systems, while Error 23 indicates a headlight fault. That’s different from the light sensor problem associated with Error 24.
If you’re dealing with another warning, or want to understand how the different faults compare, check out Upway’s Bafang error codes list. It covers common Bafang motor and controller errors, what they mean, and the first problem-solving steps to try.

💸 Want to know exactly how much your e-Bike is worth? 🚲
- Get a free estimate built on 100,000+ real sales and expert technical diagnostics.
- Use the Upway Value Estimate tool to find out in mere seconds!
What Causes Bafang Error 24?
A few things could be behind Bafang Error 24:
- Faulty light sensor circuit: The sensor isn't sending the signal it's supposed to, or something in the circuit isn't working.
- Loose or damaged wiring: Sometimes it's as simple as a loose connection. Other times, a wire is damaged, or moisture has gotten into a connector.
- Faulty display: The display may be malfunctioning or incorrectly reporting the warning.
- Controller software problem: The controller may need a compatible firmware update.
- Faulty controller: An internal problem may prevent the system from processing the sensor signal correctly.

How to Fix Bafang Error 24
Like many e-Bike error codes, start with the simplest, most common checks before spending money on replacement parts.

1. Restart your e-Bike.
Turn off the system, wait briefly, and turn it back on. If Error 24 disappears, check that the lighting controls work normally. If it returns, continue troubleshooting.
2. Inspect the headlight and wiring.
Turn off the e-Bike and remove the battery if possible. Check accessible headlight and display connectors for loose plugs, bent pins, corrosion, or damaged wires. Make sure the connectors are properly aligned and seated. And don’t force connectors together or open the controller housing unless you’re qualified to do so!
3. Test the display.
Bafang recommends testing with a known-working, compatible display. If you don’t have a spare, ask an e-Bike mechanic for help rather than buying a replacement on a guess.
4. Check the controller software.
Have a qualified technician determine whether a compatible firmware update is available for your Bafang motor and controller, and don’t install unofficial software intended for another system.
5. Test the controller.
If Error 24 persists, Bafang recommends testing with a compatible controller before replacing it. And, clearly, if the headlight isn’t working properly, pack a spare and avoid riding at night or in poor visibility until you’ve resolved the problem!
When to Contact a Bafang Dealer
If you've restarted your e-Bike, checked the wiring, and Error 24 is still showing up, it's time to get some help. But before contacting a Bafang dealer or e-Bike mechanic, figure out which motor and display you have. Also, pay attention to when the error appears. Does it happen when you turn on the bike? When you switch on the lights? Or does it come and go? If you've got a BBS02 or BBSHD conversion kit, let them know.
If your e-Bike is shutting off while you're riding, rather than showing a lighting-related warning, check out Upway's guide to why your e-Bike shuts down while riding.
Frequently Asked Questions
What is Bafang Error 24?
Can I reset Bafang Error 24?
Is Bafang Error 24 a motor Hall sensor error?
Key Takeaways
- Bafang Error 24 (24H) points to a light sensor problem on certain Bafang e-Bikes.
- Before buying parts, restart the bike and check the headlight wiring, display connections, and anything that might've worked loose.
- If the error won't go away, have a mechanic check the display and controller. There's no sense replacing expensive parts until you know what's wrong.
MY WISHLIST
Drop Us A Line
We’re happy to answer any questions you have or provide you with an estimate. Just send us a message in the form below with any questions you may have.


