...

Safe Start is live: a free 50-minute e-bike safety course, open to everyone. Get started

What Shimano E-Bike Error W011 Means 

Written by: Nick Cowie| November 17, 2026 | Time to read 5 min

Shimano’s Error W011 means that the driving speed is not detected. If the system doesn’t know how fast you’re going, it will shut off the motor to avoid breaking the system’s speed limit. Here’s how to get the detection back so you can turn assistance back on. 

More about the Author: Nick Cowie

Nick is a writer with seven years of experience in the cycling industry. In his free time, he enjoys swimming, Jiu Jitsu, and spending time outdoors.

Shimano logo in blue text
Electric bikes are distinguished from other motor vehicles through their speed and assistance rules. If you have a Class 1 or Class 2 e-Bike, it is only allowed to receive motor assistance up to the 20 mph mark. This jumps up to 28 mph for Class 3. 

If your Shimano drive unit is unable to detect how fast you are going, it is also unable to determine how much assistance you can legally get from it. When that happens, you will get a W011 error and be unable to use the motor. Let’s go over what to do if this happens to you. 

👋  Welcome to Upway!

Upway is your top destination for buying and selling e-Bikes online. Discover your next e-Bike at up to 60% off retail prices, available in new or like-new condition.




What does a Shimano W011 error mean?


The translation for the Shimano W011 error is “driving speed not detected.” When this happens, it means that the Shimano STEPS motor firmware’s data stream was interrupted, and it stopped receiving data from the rear wheel. If the central computer cannot detect the speed of the rear wheel for more than a few rotations, it will power down the system. It does this because of speed restrictions on e-Bikes that it will not be able to properly follow without driving speed detection working. 


Shimano uses “W” and “E” as their code prefixes. “W” stands for “warning,” which is less severe than an error. A warning usually represents a minor mechanical restriction, while an error can lead to long-term issues with your drive system. If you want your drive unit to be fully operational, it is up to you to find a way to give it the ability to read your bike’s speed again. 


mechanic and another man looking at e-Bikes in the shop


What steps can I take to fix it?


The most typical cause of this error is pretty simple. Sometimes the layout results in the sensor and magnet being out of alignment. If you can realign the sensor with the magnet, your speed readings from the rear wheel should come back, eliminating the warning. 


  1. Realign the Magnet and Sensor
    This is something that you can probably do on your own. Find the speed tracking sensor, which is attached to the non-driveside chainstay or rear brake caliper bracket. Then find the corresponding magnet on the wheel’s spokes or rear disc rotor. Make sure it hasn’t shifted or fallen off. Adjust the magnet manually until you can see it pass through the indicator mark that represents the sensor housing. This should line your sensor back up and bring back speed readings. 

  2. Reset the Proximity Gap
    For the sensor to properly register your speed, the gap between it and the magnet needs to fall between 3 and 17mm. If it is too close or too far away, you will not get proper speed readings. Measure the gap using a ruler or calipers to see if it is noticeably off. If you need to adjust the sensor, loosen the alignment screw with an Allen key. You can also add washers under the sensor’s body to move it closer. 

  3. Physical Interference 
    Something as simple as debris or dust can interrupt the communication between the sensor and magnet. Wipe down the magnet and sensor tip using a clean cloth. Disruptions can also be caused by faulty cord routing. Trace the speed sensor wire from the rear dropout to where it enters the frame tubes. Notice if any zip ties appear too tight or if any wires are kinked. Look for insulation tears and exposed copper, which can also cause connection issues. 

collection of bikes in the Upway warehouse


What do I do if the issue persists? 


If you run through these steps and your error is still there, you will have to make sure the sensor actually works. To do this, remove the wheel magnet entirely and power on the system. Wave the magnet by hand back and forth across the sensor and see if the speed moves from zero. If this doesn’t work, connect to your Shimano E-Tube Project app and scan for deep system faults and run a diagnostic check. If the magnet does not pick up the sensor, you might have to completely replace the sensor to get rid of your W011 error. As annoying as it can be, this is one of the less severe errors with simple fixes available. 

Frequently Asked Questions

Can a Shimano Error W011 ruin my battery?

This is one of the more minor errors that you can encounter, so you don’t have to worry about it bricking your battery. When this error comes up, usually the worst that will happen is that you might have to buy a new sensor. 

Why does debris stop the sensor from working?

Dust often contains metallic particles, and mud can be rich in iron. This metal interference can interrupt the connection between the sensor and the battery. 

Is this issue usually fixable on my own?

Yes, the Shimano W011 warning is one that you will rarely have to go to the bike shop for. Even if you need to run a diagnostic check, you can do it directly through your Shimano E-Tube Project App. 

Key Takeaways


  1. The Shimano W011 error is a minor one: Don’t freak out when this error comes up. It won’t ruin your electric bike or battery. Chances are, you will just have to readjust a sensor or, at worst, buy a new one. 
  2. Your bike shuts down to remain street legal: Because of the laws surrounding how much assistance e-Bike motors are allowed to offer at certain speeds, if the sensor cannot detect a speed, it has to shut down to avoid breaking these laws. 
  3. Upway sells Shimano products: If Shimano is your preferred drive unit, check out the Upway inventory and see our selection of refurbished e-Bikes with Shimano motors. 




There is more to Explore

Visit below articles for more info about electric bikes 

battery being installed on an e-Bike

How to Extend Your Electric Bike Battery Life

man standing next to Bianchi bike

Upway E-Bike Trade-In: Find Out What Your E-Bike Is Worth

woman on an electric cargo bike

Sell Your Bike on Upway: What We're Looking For & How It Works